Obdstart Key Master DP Plus Full

Hardware Advantages

1. Built-in VCI box

2. 8-inch touchscreen

3. Charge directly via OBD interface

4. Practical and high-end gift box

5. Industrial design with silicone sleeve.

6. Rear Bracket Design: Steering Wheel Bracket or Table Stand

7. P001 Programmer: EEPROM Adapter + RFID Adapter + Key Renewal Adapter

8. Add the SOP 8 PIN EEPROM Read Clip

9. C001/C002 circuit board for reading and writing chip data with soldering

10. IMMO Induction Coil to Detect Vehicle Key Induction Coil Failure

11. Add ECU reading wiring harness by OBD (for ECU cloning and switch activation)

Advantages of the software

1. IMMO

EEPROM

Renew Key

Key Programming

Remote Scheduling

2. Odometer Calibration

3. Diagnosis

Advanced features

1. Compatible with MAZDA CX30 2020-, MAZDA3 2020 key programming (AKL compatible and free PIN code);

2. Support PSA 2015- CONTINENTAL BSI-Q0X total loss, PIN code reading, DELPHI BSI reads PIN code by OBD in total loss, all series, all years, key programming models.

3. Support adding RENAULT/DACIA proximity keys (free PIN code) for the following models:

CAPTUR II 2021-

CLIO V 2021-

TRAFIC 2022

4. Support RENAULT/DACIA proximity key programming (free PIN code) for the following models:

TRIBBER 2018-

ARKANA 2020-

LOGAN 2020-

MEGANE IV PH2 2020-

NEW ZOE 2020-

SANDERO 2020-

5. Compatible with RENAULT/DACIA blade/proximity key programming (free PIN code) for the following models:

DUSTER PH3 2018-

6. Support JEEP COMPASS 2021 proximity 2021 all part numbers read PIN code;

7. Support CHRYSLER/ JEEP/ DODGE all series all year key programming models.

Special Functions

TPS/ABS/EPB/DPF/TPMS/SRS Reset/Fuel Injector/Gear Learning/Battery Matching/ECU Programming/Throttle Matching/

Oil Reset/Service/Steering Angle Reset/Remote Manual Setup/Electronic Steering Reset/CVT Learning/Value Reset

ECU Clone

1. ECU clone, stands for ECU duplication.

The device copies all the data from the vehicle's original ECU and then writes all the copied data to the ECU with the same hardware to perform the same ECU function with the original vehicle.

2. Clone directly when replacing a new or used ECU.

No online match in the 4S store or removal of the ECU connection cable for reading and writing! Write directly without disassembling OBD.

3. Three features for ECU cloning.

Free 4S Online: Break the 4S monopoly, benefiting the car maintenance industry

Simplified Operation Procedures – Perform Foolproof Operation

No disassembly with zero risk: read and write data without disassembling the ECU

Switch Activation Function

Today, many instruments or vehicle audio activate the secondary power supply to switch to the ignition state using CAN communication from the relevant module in the vehicle, but sometimes an instrument or audio becomes detached from the vehicle's CANBUS network, causing a start-up failure when needed. This feature can simulate CAN communication to activate the secondary power supply, so the instrument or audio enters the power on state. This way, you can not only test and verify the instrument or audio, but also save a huge cost for an automotive technician to buy a large number of multi-vehicle starter rigs and wiring harnesses.

"Help" Functions

1. Includes Integrated Testable Vehicle Models, Update Announcement, Features, Help Notes, and Wiring Diagrams, etc.

2. Update and Carlist announcement, all details are available on the device

3. Customers can search for the exclusive support features or functions on the device

4. Help Notes: Built-in help notes for each model or function

5. Wiring Diagrams: Built-in ECU wiring diagrams, more intuitive and convenient